Ask four factories to quote the same yoga set and you will get four different numbers, sometimes spread by more than a third. The usual explanation from buyers is that three of them are overcharging, or that one of them is quoting something cheaper and worse. In practice the difference is almost never greed. It comes from five inputs that each move independently: how much fabric the set consumes, how many sewing minutes the construction requires, how many dye lots the colourways need, how much trim the design carries, and how much of the run is expected to be rejected at inspection. This article walks through each input and shows how to read a quote so you can tell which factory is cheaper because it is efficient and which is cheaper because it has left something out.
There is one deliberate omission here. We do not publish per piece prices, because a yoga set is not a commodity and a number quoted out of context is a number you will end up holding a factory to when the construction is not the same. What follows is the structure, so you can test any quote you receive, ours included.
Fabric is normally the largest single line in an activewear cost sheet, and buyers usually negotiate it in the wrong unit. The price per kilogram matters, but the number that decides your cost is how many grams of fabric a set consumes once the marker is laid out and the cutting waste is counted.
A two piece set is heavier than it looks. A full length legging in a medium with a high waistband typically consumes somewhere between 0.75 and 0.95 square metres of knit, and a matching bra adds roughly 0.25 to 0.35 square metres depending on whether it is a crop with a wide underband or a strappy back. Multiply by the fabric weight and you have grams per set. At 260 GSM that is a materially different figure from the same pattern at 220 GSM, and this is why a quote for a "similar" set can be far apart with nobody behaving badly.
Three things change yield without changing the design:
Fabric composition is the other half of the line. Nylon spandex costs more than polyester spandex at the same weight, and a brushed or peached finish costs more again. Our guide to nylon spandex and GSM covers what each specification buys you in wear, because paying more for fabric only makes sense if the customer can feel the difference.
Garment labour is quoted per minute, not per garment, and the difference between a cheap set and an expensive one is almost always the operation count. Two sets photographed side by side can be 6 minutes apart on the line, and at any labour rate that gap dominates the quote.
What adds minutes:
The practical way to use this input is to ask for a construction breakdown by style, not a lump number. A factory that can tell you the operation count is a factory that has actually costed your garment. If the answer is a single figure with no breakdown, the quote is a guess with a markup on it. Our factory process walkthrough shows where those minutes go, from cutting through to the final press.
Colour is the input buyers underestimate most, because a colourway looks free on a design sheet and is anything but free in production.
Knitted fabric is dyed in lots, and each lot has a minimum weight the dyehouse will run. If you order 100 pieces of a set in one colour, you may consume less fabric than the dye lot minimum, which means you either pay for the full lot or you accept a stock colour. This is the single most common reason a 100 piece order quotes higher per unit than a 500 piece order in the same construction: the fixed dye cost is spread over a fifth of the pieces.
Colour also has to be approved before bulk, and approval is a process with its own cost in time. A lab dip is submitted, you compare it to your target under daylight, you reject or approve, and if you reject, the dyehouse adjusts and submits again. Two rounds is normal. Three rounds is a warning sign about how well the target was specified in the first place. Our guide to running a first 100 unit order covers the lab dip loop in sequence, and our activewear QC checklist lists the colour fastness tests worth insisting on.
Within a set there is an extra constraint that single garments do not have. The bra and the legging are usually cut from different rolls, sometimes different fabric qualities, and they must read as one colour when worn together. If you approve the bra fabric and the legging fabric in separate sessions, you will approve two colours that are nearly the same and visibly not the same. Approve them side by side, in daylight, before either goes to bulk.
A yoga set carries more small parts than a dress, and the trims line is where a thin quote usually hides its omissions. A complete trims list for a two piece set normally includes:
Each of these is a purchase, a stock item and an operation. When two quotes differ by a small but consistent margin, compare the trims list line by line before assuming the cheaper factory is more efficient. Very often the cheaper quote has assumed a basic elastic, no pads, a single generic care label and a plain polybag, and the moment you specify what you actually want, the two quotes converge.
Quality control does not appear on most quotes and it is in every quote. A factory that inspects at the end of the line and rejects 4 percent of output has to recover that 4 percent across the pieces that ship. A factory that inspects at three points in the process rejects less, because faults are caught before the garment is finished, but it spends more on inspection labour. Either way the cost is real and it lands in the unit price.
This is why the cheapest quote is often the one with no inspection language in it. Ask three questions: at how many points is the garment inspected, what AQL level is used for the final inspection, and what happens to a rejected piece, is it reworked, replaced or written off. Our activewear QC checklist lists the specific checks that matter on a yoga set, from seam stretch to colour fastness after washing.
Unit cost falls as quantity rises, but not evenly, and understanding the shape of the curve tells you when to stop pushing for a bigger run.
The first drop comes from cutting. Laying 100 sets means more marker ends and more waste per piece than laying 500. The second comes from dye lots, as described above: fixed dye cost spread over more pieces. The third comes from setup, pattern grading, sample approval, machine setting, all of which are paid once per style regardless of run length.
What does not fall is material and minutes. Fabric per set and sewing minutes per set are close to constant, which is why the curve flattens. In practice, most of the available saving is captured by the time a run reaches a few hundred pieces per colour, and beyond that the marginal gain is small. This is the arithmetic behind our 100 pieces per style per colour minimum: it is low enough that a first order is affordable, and it is high enough that the fixed costs are not absurd per unit. The mechanics of splitting a small order across styles and colours are in our 100 pcs private label guide.
Almost every misunderstanding about yoga set pricing comes from comparing quotes on different terms. We quote FOB from a China port, which means the price covers the garment, the trims, the packaging, the inspection, the inland transport to the port and the export documentation. It does not cover the ocean freight, the destination charges, the duty or the last mile. Those are yours, and they are yours because your forwarder can usually buy them better than we can, and because you should be able to see them.
If you are comparing our quote with one from a supplier who quotes delivered to your door, the two numbers are not comparable and the delivered number will look higher for reasons that have nothing to do with the garment. Ask every supplier to state the Incoterm on the quote. If it is not stated, the number means very little. Our article on Incoterms for clothing buyers explains what each term transfers and where the risk sits.
Line up the two quotes against the same seven questions. Any quote that cannot answer them is not yet a quote.
Once both quotes answer all seven, the gap usually explains itself, and it is usually one of two things: a different fabric weight, or a different seam package. Both are legitimate choices. Neither is a discount.
Send your tech pack with the seven points above filled in as far as you can, and the quote you get back will be usable on the first reply. If you do not have a tech pack yet, send reference images showing front, back and the strap path, plus your size chart, and we will come back with the construction questions that actually move the price.
Start from the quote request page or message our team on WhatsApp. To see the constructions we already run, browse the activewear collection, including the seamless yoga bra and legging set and the quick dry compression two piece set. The yoga wear manufacturing page summarises lead times, minimums and what a first order looks like.
One last observation from the costing desk. Buyers who get a stable price are the ones who freeze the construction before they ask for the number, and then negotiate quantity, not specification. Buyers who negotiate the specification down to hit a target price usually end up with a set that photographs well and returns badly, and the returns cost more than the saving.
Mainly because fixed costs are spread over fewer pieces. Dye lot minimums, pattern grading, sample approval and machine setup are paid once per style. Fabric and sewing minutes per set barely change with quantity, which is why the price curve flattens after a few hundred pieces per colour.
Per kilogram the price may be similar, but a heavier knit consumes more grams per set, so the fabric line rises with weight. Heavier is a construction choice, not automatically a quality upgrade, and beyond a point it makes a yoga set stiff rather than supportive.
We can give a range, but not a firm number. A quote needs the fabric weight, the seam package, the cup decision and the colour count, because those four inputs move the price more than anything else. Reference photos showing the back and the strap path are enough to start the conversation.
No, but the gap usually has a cause. Compare fabric weight, seam type, cup construction and the trims list line by line. If all four match and one quote is still lower, that is a genuinely efficient factory. If one of them is missing, the quote is for a different garment.
We quote FOB from a China port, which includes the garment, trims, packaging, inspection, inland transport and export documentation. Ocean freight, destination charges, duty and last mile delivery are arranged by your own forwarder and are not in the garment price.
Our free Buyer’s Guide walks you through MOQ, sampling, production timelines, fabric selection and QC, everything you need before placing your first order.
Read the Buyer’s Guide →