A legging forgives small errors. A sports bra does not. The same millimetre of stretch that makes a waistband feel comfortable will make a shoulder strap dig in, and a cup seam that sits two millimetres off centre will pull the whole front panel sideways once the fabric is under tension. This is why so many otherwise competent factories quote leggings happily and go quiet when a bra is mentioned. This article explains how a sports bra is actually built, what support level really means on a production floor, and how a 100 piece minimum works for a garment that uses less than half a metre of fabric.
Four reasons, and all of them are structural rather than a matter of skill.
The first is stretch direction. Knit fabric stretches in one direction more than the other, and a bra is cut so that the greater stretch runs around the body. Cut the panel ninety degrees off and the garment will grow in the wrong place after a few washes. Leggings tolerate this because the leg is a cylinder, and a cylinder forgives. A bra is a compound curve around a ribcage, and it does not.
The second is that a bra carries load. A leggings waistband carries its own weight; a bra shoulder strap carries the weight of the bust plus the rebound of every jump. Straps need a fabric with high recovery, and they need to be attached with a seam that does not creep under repeated tension.
The third is that a bra has the tightest sewing tolerances in the range. Because the panels are small, the seam allowance is a larger share of the total area. A three millimetre deviation on a legging panel is invisible; on a bra cup it changes how the two halves meet at centre front.
The fourth is fit testing. A legging can be checked on a form. A bra has to be worn, moved in, and washed before you know whether the underband rolls or the strap recovers. That testing time sits in your schedule whether or not you plan for it. Our factory process walkthrough covers the general sequence; this article covers the parts that are specific to bras.
Light, medium and high support are usually presented as a marketing choice. In production they are three different constructions, and the difference is measurable.
The practical consequence for a buyer is that support level drives the bill of materials before it drives the price negotiation. Two bras that look identical in a photo can differ by three components and two sewing operations.
This is the decision that most affects both cost and the customer experience, and it is worth settling before sampling.
Built in cups are sewn into a lining layer or bonded between two fabric layers. They give a consistent shape, survive washing without being lost, and remove a customer complaint category entirely. The trade off is that the cup position has to be right in every size, which means the pattern has to be graded specifically for the cup rather than scaled from one block.
Removable pads arrive as separate foam inserts in a pocket. They are cheaper to produce and they let one bra serve a wider range of body shapes. The cost shows up later: pads fold in the wash, migrate in the pocket, and become the most common one star review for inexpensive activewear. If you choose removable, specify pad thickness in millimetres, pad density, and pocket opening direction. A pad pocket that opens at the side will lose pads in the first wash.
Moulded cups are pre-formed on a heated press. They give the cleanest silhouette and the most predictable fit, and they suit high support and seamless constructions. The constraint is tooling: moulds are size and shape specific, so moulded cups make sense from a few hundred pieces per size upward, and less sense for a test run. If a moulded cup is essential to your design at 100 pieces, expect to use an existing mould shape rather than a new one.
Our own range covers the middle ground: the medium support compression bra uses a bonded front panel with a defined underband, the U back sculpting sports bra relies on a rib knit and a shaped back panel for its hold, and the strappy open back bra is built as light support with mesh panels where ventilation matters more than compression.
Three specifications do most of the work in a bra: fibre blend, weight, and stretch recovery.
Nylon spandex gives a soft hand, deep colour, and excellent recovery. A 72/28 nylon spandex rib at 260 GSM, the construction behind our U back bra, has enough body to hold a shape without a cup and enough stretch to sit flat against the ribcage. Nylon also takes dye deeply, which matters if you are matching a bra to a legging in the same colourway.
Polyester spandex costs less, resists chlorine and sunlight better, and holds prints well. A 78/22 recycled polyester spandex at 270 GSM is a common choice for medium support because the slightly firmer hand reads as support. The trade off is a drier hand feel that some customers notice against skin.
Recovery is the number buyers forget to ask for. A knit that stretches fifty percent and returns to forty eight percent will bag at the underband within a month. Ask for the recovery figure at a stated stretch percentage, and ask for it after five washes rather than as a single lab value. Our fabric guide for nylon spandex and GSM explains the same numbers in the context of leggings, and the logic transfers directly.
Weight deserves one warning. Heavier is not automatically more supportive. A 300 GSM knit in a light support construction produces a stiff bra that rides up, because the fabric no longer conforms to the ribcage. Weight has to match the construction, not substitute for it.
Four seam types cover almost every sports bra on the market, and each has a failure mode worth knowing when you inspect a sample.
The place a bra fails first is almost always the strap attachment, not the cup. That join takes the full load of movement, and it is the smallest seam in the garment. On a sample, pull the strap to roughly body tension and look at whether the stitch line opens. If it does at sample stage it will certainly do so in the field.
A bra that fits on a form has passed nothing. A workable protocol has four stages, and it takes about a week with three to five testers per size.
Record the results against the size chart rather than against opinion. If the underband measures correctly but rides up, the issue is construction. If the underband itself has grown, the issue is fabric. Those two diagnoses lead to completely different fixes, and separating them early saves a second sampling round. Our sizing and size chart guide explains how to write the measurements down so the results are comparable across testers.
Bras are the easiest garment in the range to run at a low minimum, for a simple reason: fabric consumption per piece is the lowest of any activewear category, typically under half a metre. A 100 piece run therefore consumes little material and blocks little cutting capacity, which is why our 100 pieces per style per colour minimum is genuinely workable here rather than a technicality.
What to watch is colour, not quantity. Each colourway carries its own dye lot minimum, and a bra in four colours can mean four lots for one style. Three patterns that keep a first bra order sensible:
What does not work is pairing a bra with a legging in the same order and treating them as one colour decision. The two garments often use different fabrics, and different fabrics dye differently even when the lab dip matches on paper. Approve the lab dips side by side, in daylight, before either goes into production. The mechanics of splitting a small order across styles and colours are covered in our 100 pcs private label guide.
A bra sample takes longer than a legging sample for the same reason it is harder to make: there is more to get wrong and less material to absorb the error. A realistic sequence from approved brief to sample in hand:
Then production runs ten to fifteen days from sample approval and deposit, which is the same as any other category. The lesson is that the sampling stage is where a bra programme loses time, so start it three weeks earlier than you would for leggings.
A brief that gets a usable quotation on the first reply contains: reference images or a technical sketch showing front, back and strap path, the intended support level and activity, cup construction preference, fabric composition and weight in GSM, your size chart with underband and bust measurements, the colourways you are considering, label and packaging requirements, and your target launch window. Add the destination country if you want a freight estimate alongside the garment price.
Send it through the quote request page or straight to our team on WhatsApp. If you want to see how the finished pieces look before you decide on construction, browse the activewear collection, and the yoga wear manufacturing page summarises what we make and how a first order runs. We quote FOB from a China port, so the international leg stays with your own forwarder and stays visible in your numbers.
One closing observation from the sample room. Brands that succeed with bras are the ones that decide the support level and the cup construction first, then choose fabric, then choose colour. Brands that start from a colour and work backwards usually end up with a beautiful bra that nobody can wear for the activity it was designed for.
With us it is 100 pieces per style per colour, split freely across sizes. Because a bra uses under half a metre of fabric, the minimum is genuinely practical here rather than a formality.
Yes, provided the photo shows the back and the strap path, not only the front. A front image alone leaves the support construction and the closure undetermined, and those are the two decisions that set the price.
Not stronger, different. Seamless removes seam bulk and skin contact, which suits light and medium support. High support usually needs cut and sew construction with defined panels, because bonding alone cannot carry that load predictably.
Usually because the pocket opening faces the wrong way or the pad is undersized for the pocket. Specify opening direction at the side seam and pad thickness in millimetres, and ask for a five wash test on the pads specifically.
No. Support comes from the underband, the panel structure and the strap attachment. A heavy knit in a light support construction produces a stiff bra that rides up instead of holding.
Our free Buyer’s Guide walks you through MOQ, sampling, production timelines, fabric selection and QC, everything you need before placing your first order.
Read the Buyer’s Guide →